Aspire PockeX and DIY e-liquid, what to mix for its two coils
The Aspire PockeX is a rechargeable all-in-one pen that turns up again and again in the hands of people starting out. For a home mixer, the real question is not whether it works but what it will take. Listings talk about wattage and battery light colours, and hardly ever about the base you should prepare. The few pieces of advice published on e-liquid do not agree with each other, and a recipe that ignores the coil soon ends in a burnt taste.
Aspire PockeX and DIY e-liquid, the short answer
The Aspire PockeX handles a homemade e-liquid without trouble, provided the ratio of your base is matched to the coil fitted. With the 0.6 ohm coil, a finished mix of 50 to 60% vegetable glycerine (VG) sits in the middle of the published advice. With the 1.2 ohm coil, a mix close to 50/50, or slightly richer in propylene glycol (PG), remains the safest choice.
Two other settings matter as much as the ratio printed on the base bottle. Flavour concentrate adds PG and shifts the real ratio, and a thicker liquid needs more time to soak the cotton before the first puff.
What the PockeX’s two coils mean for a recipe
The kit has no power setting. It runs on direct output and leaves you a single lever, the coil, which therefore sets the frame of the recipe long before you choose a flavour.
The 0.6 ohm coil in 316L stainless steel
Aspire fits the kit with a 0.6 ohm U-Tech coil in 316L stainless steel, designed for a fairly open draw. Retailers list it at 18 to 23 W. At that power the wick uses liquid quickly, which is why the thickness of the base becomes the first thing to consider.
The 1.2 ohm coil in Kanthal
The second coil, made of Kanthal, gives a tighter mouth-to-lung draw. The manufacturer presents it as the right choice for anyone who prefers an e-liquid with a higher nicotine strength. It runs cooler and draws less liquid per puff, which makes it more sensitive to a base that is too thick.
The right PG/VG ratio for the Aspire PockeX, advice that differs
For the same kit, and usually for the same 0.6 ohm coil, published recommendations cover a surprisingly wide range. Each listing presents its own figure as the obvious one.
From 50 to 70% VG for one kit
One French retailer gives a liquid of no more than 50% VG for best results with the kit. Another recommends 50% VG with the 0.6 ohm coil and accepts up to 70% as an exception. The same listing advises less than 50% VG with the 1.2 ohm coil, and points out that a VG-rich liquid clogs the coil faster.
In the UK, one shop suggests an even blend for the kit, 50/50 or 60/40 VG/PG, and advises against thicker liquids. Another pairs the 0.6 ohm coil with a ratio of around 70% VG to 30% PG, and the 1.2 ohm coil with 50/50. Between the most cautious listing and the most generous one, the share of VG moves from 50% to 70% for one and the same coil.
How we read it as mixers
These gaps mostly reflect what each seller values, vapour for some and steady wicking for others. For a homemade recipe, the middle of the range remains the most sensible starting point, which means 50 to 60% VG on the 0.6 ohm coil. Moving towards 70% can be tested afterwards, one sample bottle at a time. The reasoning behind that choice is set out in our guide to the PG VG ratio of a DIY base.
Building a DIY base that suits the Aspire PockeX
The ratio printed on the base is not the ratio of the finished bottle. Concentrate and nicotine shots are added to it, and each one weighs on the result.
Concentrate shifts the ratio
Take a 50 ml mix with 5 ml of concentrate, a 10% dose, counted as pure PG for the calculation. The base makes up the rest of the volume, with or without one 10 ml nicotine shot made up 50/50. The table gives the VG share of the finished mix, with every line worked out again.
| Base used | Final VG without a shot | Final VG with one 50/50 shot |
|---|---|---|
| 50/50 | 45% | 45% |
| 40/60 | 54% | 52% |
| 30/70 | 63% | 59% |
| 20/80 | 72% | 66% |
A 50/50 base therefore gives a mix at 45% VG, already under the 50% mark. A 20/80 base without a shot reaches 72%, beyond the most generous listing. In the UK, nicotine shots come in 10 ml bottles at no more than 20 mg/ml, and their volume is worked out on the final volume, as our method for nicotine shot dosage explains.
Which base to choose for each coil
For the 0.6 ohm coil, our preference goes to a 40/60 base, which leaves the finished mix at around 52 to 54% VG, right in the middle of the published advice. A 30/70 base suits you if you want more vapour and accept slower wicking.
For the 1.2 ohm coil, a 50/50 base is enough. It gives a mix slightly richer in PG, which travels easily into a tighter wick and matches the ratio that shops pair with this coil.
Filling the pen with a homemade e-liquid
Filling is simple, but a liquid mixed at home does not always flow like a shop-bought bottle. Two points deserve attention, the order of the steps and the time you give the cotton.
From the top, without draining the tank
The 2 ml tank, made of stainless steel and glass, fills from the top once the top cap is unscrewed. That capacity matches the 2 ml ceiling that UK rules set for refillable tanks. One retailer notes that the coil screws in at the top of the tank and can be replaced without draining the liquid, so you can switch coil values without losing the sample in progress.
Giving a thick base enough time
Aspire asks you to let the cotton become fully saturated before the first puff, allowing around two to three minutes depending on how thick the liquid is. A shop goes further and advises five minutes before using a new coil. With a 30/70 base or anything richer, the second instruction is the more cautious one.
What a homemade recipe changes for the wick
A DIY recipe does not wear a coil in the same way as a shop-bought e-liquid. Two factors make the difference, the VG content and the make-up of the flavour.
Ingredients that gunk up the coil
A very sweet recipe, or one heavy in sweetener, generally clogs the wick faster than a dry flavour. On a small coil such as the one in the Aspire PockeX, that build-up shows as a flavour that fades, then as a burnt note.
One label per bottle
Write the base, the concentrate dose and the coil used for the first test on every bottle. If the flavour drops off quickly, that note tells you whether to rethink the ratio, the flavour or simply change the coil.
FAQ
These five questions come up often when you fill an all-in-one pen with your own mix.
Is the PockeX a good device for tasting your first recipes?
Yes, for one specific reason. With no power setting, it removes a variable, and two sample bottles tasted on the same coil, at a similar battery level, differ only by their recipe. Battery level matters because, on direct output, power follows the voltage of the battery.
Can you switch from one recipe to another without changing the coil?
Yes, but the cotton keeps a trace of the previous recipe, especially after a strong flavour such as menthol or aniseed. To compare two recipes fairly, a fresh coil for each gives a clearer verdict than simply changing the liquid.
Should you wait until steeping is finished before filling the tank?
It is not compulsory, but a young recipe can taste flat and tempt you to add too much concentrate. It is better to judge a mix after its rest period, described in our article on steeping e-liquid.
Can you vape an unflavoured base in the PockeX?
Technically yes, the coil makes no distinction. The point is limited to checking, for instance making sure a new coil gives no stray taste before you test a recipe in it.
What should you do if a homemade e-liquid makes the coil crackle?
Crackling often signals too much liquid around the wick or a base too thin for the coil fitted. Check the level, avoid going above the maximum fill mark, and try a base slightly richer in VG if it carries on.
Aspire PockeX for DIY, the settings to remember
Three decisions are enough to set up a recipe, the coil, the base and the priming time. Starting from a 40/60 base on the 0.6 ohm coil and a 50/50 base on the 1.2 ohm coil, counting the PG added by the concentrate and giving the cotton five minutes covers the essentials.
Advice on VG varies from one listing to the next, but working out the finished mix lets you decide without relying on a single page. With the Aspire PockeX the hardware stays simple, and it is the care taken in preparation that shapes the result, as with any homemade e-liquid.
Editorial content for adult readers only. Vaping products can contain nicotine, which is a highly addictive substance. Vaping products are not for sale to anyone under 18 in the UK. This article is not a buying recommendation.